Site Information
Your path: Home >> News >>
What kind of shook his head lamp repair techniques
Tips 1: Please prepare a small paper box or something like that to Sheng easily lost screw, it is best served in a small interval of intraday and in accordance with the order of installation, although they roughly the same size thread and Stud , but the length will be different - so much more easier to distinguish Philippe Starck Bedside gun lamp Wilhelm Wagenfeld Bauhaus Lamp Glass Base Flos Miss K table lamp Pio and Tito Toso Blow Table Lamp Vico Magistretti Atollo Table Lamp Flos Spun Light T1 table lamp Flos Spun Light T1 floor lamp Achille Castiglioni Arco floor Lamp Poul Henningsen Artichoke lamp Verner Panton Globe pendant Poul Christiansen Le Klint 172 Pendant Lamp.
Tips 2: Unplug the power, you can remove the shell of the lamp lights. A first step, the problem with the naked eye to see where this can be seen light after cleaning is not easy to see out of the issue: for example, due to leakage caused by a dirty circuit board in the trackingmarks it is easy to see out of However, after cleaning the contrary, it is difficult to see them (although these are most likely caused by dust problems!
Tips 3: In the maintenance circuit board before, he must wear anti-static hand band, can be the body's own static boot to the ground. If you do not, there will be danger of damage to components: Think about it, just walking on nylon carpet, it can produce up to 12,000 volts of static electricity! So, it must not ignore the static electricity hazards.
Tips 4: Test End and identify the problems, you can start cleaning work. First, use the vacuum cleaner dust as siphoning off the best that can be used with a small brush scoparia, clean up particularly thorough. Particular attention to fans around the place, where the accumulation of dust up. Circuit will usually cast a thick layer of dust, because the high-voltage circuit has a special large dust absorption edge, like a magnet, like iron absorption. Circuit board will require additional cleaning, most of the electronic components suppliers to provide a dedicated aerosol cleaners. Should pay particular attention to alcohol use, because it can dissolve the protective layer circuit board, and will damage part of the components. Remove the circuit board in the small devices or connectors to do cleaning, pay attention to their original location so as to avoid wrong direction.
Tips 5: shaking his head in a clean light into the optical components should be extremely careful, because the glass pattern pieces with dichroic filters are very easy to scratch - these are places where scratched when projected through the pattern is particularly evident, if not with a special cleaning agent, it's very easy to damage the lens surface. To use industrial alcohol to clean the mirrors, lenses, pattern sheets and filters, and rinsed with distilled water (Martin pro series lamps also require the use of special protection of lens elements added to the water to wash, such as the Kodak photo cleaning agent to prevent the lens appears stripes and small spots), but also with the anti-static cloth or hair dryer to dry the lens. Pay particular attention to remove the lights when not to touch bulb with bare hands, because through many years of use, light bulbs on the surface will be thinner and easier to break. Tips 6: Check that some loose parts or has used a very old drives. Mechanical components can not always have to maintain the best condition, belt use for a long time, will have less flexibility, which led to displacement of dollars of parts. Replacing light bulbs, and then install a good light shell, check the small box inside are there any left screws. Take a look at there is no problem, you can pta test.
Finally: According to the testing program test lamps, usually use the built-dmx address the specific code to carry out. Check there are no unusual circumstances, the pattern pieces are arranged, the light gate or color films and so is business as usual. After the lamp warm is the best time to check the light bulb: The beam projected onto a flat plane, and adjust the exposure to the most central point of light bulbs, usually using the three adjustment screws behind the lamp, and slowly the location of the light bulb Debugging is good, until the date of the projection beam uniformity.,
Tips 2: Unplug the power, you can remove the shell of the lamp lights. A first step, the problem with the naked eye to see where this can be seen light after cleaning is not easy to see out of the issue: for example, due to leakage caused by a dirty circuit board in the trackingmarks it is easy to see out of However, after cleaning the contrary, it is difficult to see them (although these are most likely caused by dust problems!
Tips 3: In the maintenance circuit board before, he must wear anti-static hand band, can be the body's own static boot to the ground. If you do not, there will be danger of damage to components: Think about it, just walking on nylon carpet, it can produce up to 12,000 volts of static electricity! So, it must not ignore the static electricity hazards.
Tips 4: Test End and identify the problems, you can start cleaning work. First, use the vacuum cleaner dust as siphoning off the best that can be used with a small brush scoparia, clean up particularly thorough. Particular attention to fans around the place, where the accumulation of dust up. Circuit will usually cast a thick layer of dust, because the high-voltage circuit has a special large dust absorption edge, like a magnet, like iron absorption. Circuit board will require additional cleaning, most of the electronic components suppliers to provide a dedicated aerosol cleaners. Should pay particular attention to alcohol use, because it can dissolve the protective layer circuit board, and will damage part of the components. Remove the circuit board in the small devices or connectors to do cleaning, pay attention to their original location so as to avoid wrong direction.
Tips 5: shaking his head in a clean light into the optical components should be extremely careful, because the glass pattern pieces with dichroic filters are very easy to scratch - these are places where scratched when projected through the pattern is particularly evident, if not with a special cleaning agent, it's very easy to damage the lens surface. To use industrial alcohol to clean the mirrors, lenses, pattern sheets and filters, and rinsed with distilled water (Martin pro series lamps also require the use of special protection of lens elements added to the water to wash, such as the Kodak photo cleaning agent to prevent the lens appears stripes and small spots), but also with the anti-static cloth or hair dryer to dry the lens. Pay particular attention to remove the lights when not to touch bulb with bare hands, because through many years of use, light bulbs on the surface will be thinner and easier to break. Tips 6: Check that some loose parts or has used a very old drives. Mechanical components can not always have to maintain the best condition, belt use for a long time, will have less flexibility, which led to displacement of dollars of parts. Replacing light bulbs, and then install a good light shell, check the small box inside are there any left screws. Take a look at there is no problem, you can pta test.
Finally: According to the testing program test lamps, usually use the built-dmx address the specific code to carry out. Check there are no unusual circumstances, the pattern pieces are arranged, the light gate or color films and so is business as usual. After the lamp warm is the best time to check the light bulb: The beam projected onto a flat plane, and adjust the exposure to the most central point of light bulbs, usually using the three adjustment screws behind the lamp, and slowly the location of the light bulb Debugging is good, until the date of the projection beam uniformity.,
2009-9-23
E-mail: sales@designlamps.net TEL: +8613923852390
Copyright © 2005 www.designlamps.net All Rights Reserved
